Nanjing Ranran Tiancheng's natural gas drying oven serves industrial drying, paint baking, coating curing, preheating and thermal holding.
Compatible with natural gas or LPG, it adopts imported modulating gas burners, closed forced air circulation and digital PID temperature control.
Airflow supports horizontal or vertical layout, with automatic ignition, flame monitoring and multi-stage safety interlocks. Each unit is configured to match material properties, target temperature, batch throughput and workshop layout.
Gas Heating System and Working Principle
The gas burner generates heat through controlled combustion. Heat transfers to circulating air via heavy-duty heat exchanger, fully separating combustion exhaust from process air to prevent workpiece contamination.
A high-flow circulation fan pushes heated air through internal ducting into the working chamber. After heat exchange with loaded products, air returns to the heating zone for continuous circulation.
Temperature sensors feed real-time chamber readings back to the controller, which modulates burner firing rate proportionally to stabilize set temperature.
Main Heating Components
Gas Burner: Imported modulating model; capacity selected based on chamber volume, temperature requirement and cycle load
Combustion Control Assembly: Pre-purge cycle, ignition sequence, flame monitoring, proportional firing adjustment
Circulation Fan: Delivers uniform air distribution inside the chamber
Air Duct Assembly: Horizontal / vertical airflow layout, configurable
Thermal Insulation Layer: 100mm aluminum silicate cotton, cuts radiant and convective heat loss
Final component specifications are confirmed in the approved technical proposal.
Temperature Uniformity and Air Circulation
Three thermal indicators are defined for process validation (tested under full load, steady state after 30min soak):
Temperature Control Accuracy: ±2°C
Temperature Uniformity: ±3°C
Temperature Stability: Maintained within ±1°C during continuous running
Uneven temperature leads to inconsistent residual moisture, coating defects and unstable curing results.
Our optimized baffle and circulation duct design eliminates dead zones and hot spots. For critical coating and precision curing processes, we deliver a formal temperature mapping report before shipment; all test points, loading pattern and hold duration are agreed at quotation stage and documented in the technical proposal.
Gas Burner Safety and Protection System
Gas safety devices are classified as standard or optional according to the selected configuration and project requirements.
Standard Safety Configurations
- Automatic pre-purge before ignition
- Continuous UV flame monitoring
- Automatic gas shut-off valve on flame loss
- Over-temperature protection with burner cut-off
- Emergency stop button
- Gas leak detection alarm
Optional Safety Configurations (on request)
- Low / high gas pressure monitoring & interlock
- Explosion relief structure
- Low-NOx burner upgrade (NOx ≤60 mg/Nm³)
- Dedicated exhaust monitoring
Applications
This oven supports processes including coating curing, powder coating baking, solvent removal, moisture drying, stress relieving, preheating before machining, constant-temperature ageing and post-treatment stabilization.
It serves industries such as automotive parts, metal fabrication, hardware finishing, composite materials, new energy components, construction materials, fine chemicals and custom laboratory thermal processing.
|
Parameter |
Description |
|
Equipment Type |
Natural Gas / LPG Indirect-Fired Drying Oven |
|
Heat Source |
Natural Gas or Liquefied Petroleum Gas |
|
Temperature Range |
Ambient to 250°C |
|
Heating Unit |
Imported modulating gas burner |
|
Temperature Controller |
PID digital intelligent control |
|
Circulation Mode |
Forced hot air circulation |
|
Airflow Direction |
Horizontal / Vertical, optional |
|
Insulation |
100mm aluminum silicate cotton |
|
Outer Shell |
Cold-rolled steel / 304 Stainless steel, optional |
|
Ignition & Detection |
Automatic ignition + continuous UV flame monitoring |
|
Standard Safeguard |
Over-temperature protection, flame-loss shut-down, gas leakage alarm |
|
Rated Inlet Gas Pressure |
Natural gas: 8–25 kPa; LPG: 20–50 kPa |
Customized Design and Equipment Selection
Equipment selection is based on the following process and installation requirements:
- Material characteristics, initial moisture content and target moisture level
- Required working temperature and holding time
- Batch weight or hourly throughput
- Max workpiece dimension for chamber sizing
- Daily running shifts and continuous operation demand
- On-site fuel type and stable gas supply pressure
- Available floor space, access and maintenance clearance
Customization scope
- Internal chamber dimensions
- Tray / trolley loading structure & capacity
- Horizontal or vertical airflow layout
- Burner heat load matching
- Shell material selection
- Power voltage & frequency adaptation (380V/415V 50/60Hz)
- Exhaust and waste-gas ducting design
- HMI / remote monitoring upgrade
Send the above process data, our engineers will recommend a matched design.
Manufacturing, Quality Control and Delivery
All fabrication strictly follows approved technical drawings. Structural welding, insulation installation, gas piping, electrical wiring and burner assembly are inspected stage by stage under IQC / IPQC / OQC procedures, complying with ISO 9001.
Pre-shipment inspection checklist
- Chamber dimension & structural integrity check
- Insulation construction inspection
- Gas pipeline tightness & leakage test
- Electrical insulation and wiring verification
- Fan running balance test
- Burner ignition and flame stability test
- Temperature control & safety interlock function test
- Steady-state temperature uniformity mapping test (if required by contract)
Factory test report, as-built drawings, operation & maintenance manual, spare parts list, CE certificate will be provided on shipment.
Order & Delivery Terms
MOQ: 1 unit
Lead time: 18–25 working days, confirmed after drawing approval
Packing: Export plywood case
Trade terms: FOB / DDU / DDP available
Warranty: 12-month warranty on core burner and control components, terms detailed in sales contract
After-sale support: Remote troubleshooting guidance; on-site commissioning service available upon request; long-term spare parts supply available
FAQ
Q: Are you a manufacturer or trading company?
A: We are direct manufacturer based in Nanjing, Jiangsu, specializing in industrial indirect gas-fired drying and curing ovens.
Q: Are combustion exhaust and drying circulating air separated?
A: Yes, indirect heat exchange design isolates flue gas from process air to avoid workpiece contamination, ideal for coating and high-purity drying.
Q: What does the warranty cover?
A: 12-month warranty for manufacturing defects of main burner, controller and structural parts; normal wearing consumables (seals, filters, gaskets) are excluded. Full scope written in sales contract.
Hot Tags: natural gas drying oven, China natural gas drying oven manufacturers, suppliers, factory, electric blast drying oven, Explosion proof Steam Oven, Explosion proof Vacuum Box, Hot Air Circulation Oven, industrial oven, Mould Preheating Oven

